Features & BenefitsEnhances existing ventilation via felt/membrane lap jointsOffers 3,000mm2 additional free vent area per Lap VentSuitable for rafter spacings from 400-600mm centresEasy to install2 spring clips to secure in placeManufactured from recycled PolypropyleneHow many Lap Vents do I need?This will vary dependent on the level of extra ventilation required and length of the roof.To provide typical ventilation, allow for 1 lap vent every alternate rafter space at low level, on opposite sides of the roof. If maximum ventilation is required, install at high level and every rafter space along the full length of the roof.Each lap vent provides 3,000mm2 of additional free airflow and is suitable for rafter spacings from 400-600mm centres.It is recommended that one lap vent should be installed into every alternate rafter space at low level. If further ventilation is required, install one lap vent into every rafter space at low level or into lap joints at higher level.The lap vents should be fitted to both sides of the roof space in order to provide cross-flow ventilation.How to install:1. Ensure the lap vent is orientated with clips facing inwards to the roof space and the flat surface to roof.2. Insert the pointed edge of the lap vent into the gap between membrane/underlay overlap and then push flat towards roof line.3. Push the lap vent down inside the joint ensuring the clips hook onto the outer face.4. The lap vent is in the correct position when the clips are fully engaged onto the top edge of the membrane/underlay. Repeat the installation process with further lap vents until the required ventilation rate is achieved.
12x 310ML Lumberjack Polyurethane Wood Adhesive Gel - 5-Minute Setting
1L Leadmate Patination Oil Flashing Protection Coating Cleaning
1Mtr Bird Comb Protection Eaves Filler - Roof Tile Gap Fillling
Features & BenefitsEnhances existing ventilation via felt/membrane lap jointsOffers 3,000mm2 additional free vent area per Lap VentSuitable for rafter spacings from 400-600mm centresEasy to install2 spring clips to secure in placeManufactured from recycled PolypropyleneHow many Lap Vents do I need?This will vary dependent on the level of extra ventilation required and length of the roof.To provide typical ventilation, allow for 1 lap vent every alternate rafter space at low level, on opposite sides of the roof. If maximum ventilation is required, install at high level and every rafter space along the full length of the roof.Each lap vent provides 3,000mm2 of additional free airflow and is suitable for rafter spacings from 400-600mm centres.It is recommended that one lap vent should be installed into every alternate rafter space at low level. If further ventilation is required, install one lap vent into every rafter space at low level or into lap joints at higher level.The lap vents should be fitted to both sides of the roof space in order to provide cross-flow ventilation.How to install:1. Ensure the lap vent is orientated with clips facing inwards to the roof space and the flat surface to roof.2. Insert the pointed edge of the lap vent into the gap between membrane/underlay overlap and then push flat towards roof line.3. Push the lap vent down inside the joint ensuring the clips hook onto the outer face.4. The lap vent is in the correct position when the clips are fully engaged onto the top edge of the membrane/underlay. Repeat the installation process with further lap vents until the required ventilation rate is achieved.
20kg Cure It Glass Guard Roofing Resin
Glass Guard Roofing Resin has been specially formulated for use on GRP flat roofing systems and is adjusted for cure times in all seasons. GRP (or fibreglass) roofing creates a long-lasting and low maintenance flat roofing solution, whilst being safer and more environmentally friendly to install than some traditional roofing methods.This high-quality resin is backed by a 10-year manufacturer guarantee when used in the correct manner and is suitable for both domestic and commercial applications. Glass Guard roof resin is also fire retardant when used in conjunction with slate granules (Slate granules should be applied to the topcoat at a rate of 0.75kg/m² for fire certification - BS476 Part 3:2004) and is used in conjunction with fibreglass matting.
20KG Setting Sand Narrow Joint Paving Filler Jointing Compound Buff
25kg Cure It GRP Slate Granules
Cure It GRP Fibreglass Roofing Non Slip Slate Granules for addition to the GRP Top Coat when wet to add grip - 25kg Bag.Slate granules are used either for decorative purposes or to make a non-slip walk way.
300mm Anchorset Green Chemical Anchor Concrete Masonry Resin Glue Box of 12
310ML Lumberjack Polyurethane Wood Adhesive Gel - 5-Minute Setting
400ML Jumbo Mitre Fast Fix Super Glue Bonding Kit 100G Glue Activator Pack of 6
Features & BenefitsEnhances existing ventilation via felt/membrane lap jointsOffers 3,000mm2 additional free vent area per Lap VentSuitable for rafter spacings from 400-600mm centresEasy to install2 spring clips to secure in placeManufactured from recycled PolypropyleneHow many Lap Vents do I need?This will vary dependent on the level of extra ventilation required and length of the roof.To provide typical ventilation, allow for 1 lap vent every alternate rafter space at low level, on opposite sides of the roof. If maximum ventilation is required, install at high level and every rafter space along the full length of the roof.Each lap vent provides 3,000mm2 of additional free airflow and is suitable for rafter spacings from 400-600mm centres.It is recommended that one lap vent should be installed into every alternate rafter space at low level. If further ventilation is required, install one lap vent into every rafter space at low level or into lap joints at higher level.The lap vents should be fitted to both sides of the roof space in order to provide cross-flow ventilation.How to install:1. Ensure the lap vent is orientated with clips facing inwards to the roof space and the flat surface to roof.2. Insert the pointed edge of the lap vent into the gap between membrane/underlay overlap and then push flat towards roof line.3. Push the lap vent down inside the joint ensuring the clips hook onto the outer face.4. The lap vent is in the correct position when the clips are fully engaged onto the top edge of the membrane/underlay. Repeat the installation process with further lap vents until the required ventilation rate is achieved.
50 x Grey Dry Verge System Universal Fit For Gable/Apex Roofs Bundle
500ML Leadmate Patination Oil Flashing Protection Coating Cleaning
50G Mitre Fast Bonding Kit Glue & 200ML Activator Adhesive
5L Black Thompsons One Coat Roof Seal
Thompsons One Coat will protect your roof with just one coat. Product details Size: 5 L Material: SB Bitumen Colour: Black Usage: Exterior Coverage: 5-7 m2 Type: Roof Seals Features & benefits Get the job done in a single coat Flexes with the natural movement of the roof Outperforms traditional bitumen coatings
5L Cure It GRP Concrete Primer
Cure It GRP Fibreglass Roofing G4 Concrete Primer 5kg for use as a substrate primer when bonding GRP to concrete.
5L Lumberjack Clear Fast-Drying Wood Preserver
750G Lumberjack 5-Minute Wood Adhesive Professional D4 Polyurethane
Aarondec Diamond Cut Promenade Tile
Aarondec Imperial Promenade Tile
Acrypol Plus With Fibres waterproof roof coating was specifically developed to provide a solution for carrying out the day to day maintenance requirements of those involved in roof waterproofing protection.
Inline Slate Vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
C1 Cure It GRP Universal External Corner
C1 universal external corner for use with all A and B trims to form a left or right hand corner.
C3 Cure It GRP External Fillet Corner
C3 external fillet corner is used as a preformed external corner for all D-trims. Avoids mitring in situ.
C3 Cure It GRP Internal Fillet Corner
Cure It GRP C3 Internal / External corner fillet GRP edge trim used as a pre-formed internal / external corner for the D260 fillet trim to avoid the need for mitring in situ.
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Cure it 12m2 GRP Accessory Starter Pack.
Cure It GRP Fibreglass Roofing Acetone used for cleaning tools, spillages and as a surface decontaminant.
Cure It GRP Catalyst Safety Dispenser
Cure-It GRP Hardener Safety Dispenser is a great way to measure the exact amount when installing Cure-It GRP flat roof systems. It has a 15ml dispensing flute which ensures accurate measurement and dispensing of Cure-It Hardener.
The Cure-It Aluminium extension pole is made to fit with Cure-It soft rollers and paddle rollers.
Cure It GRP Swivel Sanding Pad
This Cure It Swivel Sanding Pad is used for sanding off large flat GRP roofing areas.
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system.
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system.
Easy Tray Ridge Hip Support Tray Accessory Kit Universal Dry Fix Mortar Free
EASYVerge U Universal Verge System Pack of 50 - Various Colours
The GRP flat flashing trim is a versatile flat section of GRP that can be used to clad surfaces prior to top coating and can be used where a pitched roof meets the flat roof surface. PU trim adhesive should be applied and the trim held in place with pins prior to matting.
Features & BenefitsEnhances existing ventilation via felt/membrane lap jointsOffers 3,000mm2 additional free vent area per Lap VentSuitable for rafter spacings from 400-600mm centresEasy to install2 spring clips to secure in placeManufactured from recycled PolypropyleneHow many Lap Vents do I need?This will vary dependent on the level of extra ventilation required and length of the roof.To provide typical ventilation, allow for 1 lap vent every alternate rafter space at low level, on opposite sides of the roof. If maximum ventilation is required, install at high level and every rafter space along the full length of the roof.Each lap vent provides 3,000mm2 of additional free airflow and is suitable for rafter spacings from 400-600mm centres.It is recommended that one lap vent should be installed into every alternate rafter space at low level. If further ventilation is required, install one lap vent into every rafter space at low level or into lap joints at higher level.The lap vents should be fitted to both sides of the roof space in order to provide cross-flow ventilation.How to install:1. Ensure the lap vent is orientated with clips facing inwards to the roof space and the flat surface to roof.2. Insert the pointed edge of the lap vent into the gap between membrane/underlay overlap and then push flat towards roof line.3. Push the lap vent down inside the joint ensuring the clips hook onto the outer face.4. The lap vent is in the correct position when the clips are fully engaged onto the top edge of the membrane/underlay. Repeat the installation process with further lap vents until the required ventilation rate is achieved.
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system.
Flat Glass Roof Light on 150mm PVC Kerb (Unvented, Non-Opening)
Flat Glass Roof Light on Builders Upstand (Unvented, Non-Opening)
The Manthorpe Flash Vent is a simple one piece roll-out, easy fit sheet that provides ventilation for abutment roof details, providing a weather-tight solution to the need for a continuous 5mm² of airflow. As it is made from just one component it is economical and easy to install. The roll-out system makes fitting a breeze as it is supplied in a handy box dispenser with no need for specialist fixing tools. Manthorpe’s Research and Development team has addressed the need for a flexible and effective system by incorporating a series of nodules into the design on both sides of the flexible vent roll. This not only provides the required airflow but includes an integral fly screen and maximises support of the lead. The product has been independently wind tunnel tested for weather tightness and can be used over profiled tiles, non profiled tiles and slates without compromising its effectiveness. Two widths can also be joined together to fit any length of lap between the lead and the tiles.
Grey Cure It GRP Trim Adhesive
Used for bonding GRP trims around the perimeter of the roof.
Grey Manual Blackout Blind, White Channels (780x980mm) DKL MK04 0705SWL
Cure It Brushes for the ultimate finish.
Our Cure-It Complete Rollers have been designed for use in the installation of a GRP waterproofing system to apply Roofing Resin and Topcoat. They are available in both 3 and 9" sizes and can be further extended with Cure-It's extension pole.
MEKP catalyst/hardener for the addition to Cure It Roofing Resin & Topcoat. Hardener can be supplied in different strengths to compensate for seasonal variations in temperature, we stock the complete seasonal range.
MEKP catalyst/hardener for the addition to Cure It Roofing Resin & Topcoat. Hardener can be supplied in different strengths to compensate for seasonal variations in temperature, we stock the complete seasonal range.
Cure-It Paddle Rollers have been designed for use in the installation of a GRP waterproofing system to consolidate the resin and chopped strand matting . They can be further extended with Cure-It's extension pole.225mm, 140mm, and 70mm metal paddle rollers for consolidating the laminate.Removes air from roofing laminate and ensures thorough saturation of reinforcement mat.
Cure-It's Reinforcement Mat is used during the installation of a GRP waterproofing system. The mat is laid down and subsequently covered with Roofing Resin in order to form the laminate component of the system. 450g/m2 thickness is suitable for most roofs.
Resin and topcoat application roller for detail work.Does not break down with exposure to styrene.Available in 9", 6" or 3"
Cure It GRP Fibreglass Roofing Topcoat 20 kg provides the finished colour and surface appearance.
Key Features:Size: 20kgColour: Clear20kg Coverage: 13.5 sqmApplications: Flat roofs, industrial applications, pitched roofs, walkways, balconies, green roofs. steps, complex gulleys / guttersGuarantee: 25 Year Product Guarantee
Cure It GRP Fibreglass Reinforcement Bandage is used as a reinforcement for forming corners and other detailed areas of the roof.Width: 75mmLength: 75mUse: Reinforcement Bandage is used as a reinforcement for forming corners and other detailed areas of the roofGuarantee: 25 Year Product Guarantee
Compatible with the Timloc Inline Slate Vent RTV-IS Simply click into position to secure the adapter to spigot of the tile vent Provides a precise fit to 110mm duct or Soil Vent Pipe Adapter sits below the roof batten to provide a simple, neat installation
Interlocking Plain roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Isoflex Liquid Rubber 750ml- 2.1L- 4.25L Liquid Rubber Waterproofing
Hall clips are a fast and efficient way to fix lead sheet into a joint. Fix lead flashings up to 20 times faster than with lead wedges. The Hall Clip firmly grips lead in place and is installed literally in seconds without the use of any special tools.Hall Clips come supplied in bags of approximately 50 clips which are small enough, and light enough, to easily fit the tool box or pocket and will secure any flashings in a chase from 6mm to 18mm.Features:
All-purpose adhesive for fixing to base material or for overlapping. High performance sealant and adhesive with a high grip strength. Forms a durable bond to tiles, slates, mortar and brickwork. Contains no acids.
Leadax Lead Replacement Flashing
Aluminium expanded metal on both sides with a layer of modified polyvinyl butyral, with a removable protective film on either side of the product. Leadax is patented. Manufactured from waste material, destined for landfill. This makes Leadax unique as a lead alternative and contributes to making the world more sustainable. Roll lengths of 6 metres (3.85 kg per square metre and thus 75% lighter than 18 pounds or code 4 lead).
Easily and efficiently mould your Leadax flashing around tiles, uneven surfaces and other more problematic areas of your roof with the Cromar Leadax Roller. Comes with a simple, user-friendly design that produces professional results on any roof.
Easily and efficiently mould your Leadax flashing around tiles, uneven surfaces and other more problematic areas of your roof. Comes with a simple, user-friendly design that produces professional results on any roof.
These Leadax scissors will cut your Leadax to size quickly and easily to ensure a perfect finish to your job.
Lumberjack Polyurethane Wood Adhesive Box of 12 - 30-Minute Setting
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Multi Duct Adapter (150/125/110/100)
Provides a precise fit to 110mm duct or soil vent pipe Trim along the indented edges to configure the duct size Provides a precise fit to 100/110/125/150mm duct 110mm outside diameter fits directly to Timloc Tile Vent spigots Compatible with flexible, semi-rigid and rigid duct Can be secured with adjustable screw clamps, zip ties or glued/screwed
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system.
Pack of 10 Felt Lap Vent Loft Attic And Roof Ventilation Airflow G630
Pack of 20 Felt Lap Vent Loft Attic And Roof Ventilation Airflow G630
Pack of 50 Felt Lap Vent Loft Attic And Roof Ventilation Airflow G630
Plain roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Compatible with Timloc Plain Inline Roof Tile Vents RTV-P / RTV-IP without reducing the free vent area of the system Simply click into position to secure the adapter to base of the tile vent Provides a precise fit to 110mm duct or Soil Vent Pipe Duct can be secured to the adapter with adjustable screw clamps, zip ties or glued/screwed
Plasterers Scrim Mesh Plasterboard Joint Scrim Tape Fibre Jointing Tape
Plasterers Scrim Mesh Plasterboard Joint Scrim Tape - 48mm X 90 Metre Scrim is a premium quality, quick and easy to apply, self-adhesive scrim tape that is made in Europe to perform. Scrim has a quality high tack adhesive and an open mesh that will not blister or bubble, creating perfect joints every time. Benefits Quick and easy to apply. · Self-adhesive – eliminates the need for pre-plastering. · Flexible – won’t bubble or blister. Areas For Use · For jointing dry walling. · For repairing/jointing over large cracks in plaster. · Repairing/jointing in ceiling work. Limitations · Ensure surfaces are completely clean before applying tape. · Never overlap the tape, always butt the joint. · When applying jointing compound or plaster, ensure complete penetration through the tape to achieve optimum adhesion. Surface Preparation All surfaces must be clean, dry, sound and free from oil, grease and dust.
Roof & Gutter Waterproof Adhesive Sealant Black Pack of 6
Sahara Plain Square Ceiling Tile
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
TF200 Housewrap Protect Thermo Insulating Breather Membrane (2.7 x 100m)
Profiled roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Universal Angled Apex End Cap - Dry Verge Unit Gable Roof
Universal Dry Verge Kit - System, Starter, End Cap & Ridge Cap
Universal Half Round Apex End Cap - Dry Verge Unit Gable Roof
Universal roof tile vent to enable ventilation directly into a roof space or connect to a ducted ventilation system
Vent 3 Light 95g Breathable Membrane
Vent3 Light is a lightweight triple layer fabric, high performance breather membrane, made from high tensile spun bonded polypropylene layers, around a micro-porous polypropylene film. Designed for use as a universal breather membrane for roofs and walls boasting superior moisture vapour permeability. Vent3 Light has a printed (dark grey) upper surface with preprinted marking lines and a white under-face. The high vapour permeability and waterproof properties of the membrane, combined with excellent tensile/tear strength, make Vent3 Light an ideal product for use in all pitched roof applications. It will allow the escape of water vapour from within the roof structure whilst protecting against wind driven rain, snow and dust which may penetrate the main roof waterproofing, providing a permanent quality breather underlay, which will last the life of the roof construction.
Vent 3 Pro 165g Breathable Membrane
Vent3 Pro is a heavy weight, triple layer fabric, high performance breather membrane, made from high tensile spun bonded polypropylene layers, around a micro-porous polypropylene film. Designed for use as a universal breather membrane for roofs and walls boasting superior moisture vapour permeability. Vent3 Pro has a printed green upper surface with preprinted marking lines and a white under-face. The high vapour permeability and waterproof properties of the membrane, combined with excellent tensile/tear strength, make Vent3 Pro an ideal product for use in all pitched roof applications. It will allow the escape of water vapour from within the roof structure whilst protecting against wind driven rain, snow and dust which may penetrate the main roof waterproofing, providing a permanent quality breather underlay, which will last the life of the roof construction.
